InCarTec 29-655 Alfa Romeo 147, 156, GT Steering Wheel Audio Control Interface & ISO Cable
- Stock Status: In Stock
- Item Condition : New
- Available QTY : 5
- Brand: InCarTec
- Model: 29-655
- EAN: 7427307020877
- Warranty: 2 Years Warranty
Description
Car Audio Steering wheel interface and ISO cables allowing use of original buttons with a new aftermarket head-unit. This interface will retain the use of the steering wheel audio controls with an aftermarket head unit.
This interface is designed for vehicles that have permanent and ignition power feeds in the ISO connector in the dashboard. Some cars only have a permanent power supply and use the CAN bus signal to turn on the radio, for these cars a separate ignition power will need to be supplied or use 29-655-CAN interface with a built in CAN ignition interface.
Product Compatibility Chart
| Make | Model | Years | Notes |
| Alfa Romeo | 147 | 2000 - 2010 | (Type 937) (Pre-CANBUS vehicles only) |
| Alfa Romeo | 147 | 2002 - 2005 | GTA (Pre-CANBUS vehicles only) |
| Alfa Romeo | 156 | 1997 - 2005 | (Type 932) (Facelift cars and cars with original OEM navigation) |
| Alfa Romeo | 156 | 2002 - 2005 | GTA (Facelift cars and cars with original OEM navigation) |
| Alfa Romeo | GT | 2004 - 2010 | (Type 937) (Pre-CANBUS vehicles only) |
The years stated refer to the model's years of manufacture, please check the item description for information about any changes there may be within these productions years.
If the car is fitted with a Bose System please use part number 20-266 with this interface
There are small amount of cars pre-2007 that have CANBUS ignition. Before ordering please remove the original radio as the vast majority of original radios have a useful wiring diagram on the chassis. Remove the original radio and check, if illumination and switched power are showing on pin 2 and 3 of the diagram then it does not have CAN ignition and 29-655 is the correct interface for you
If Illumination and switched power are missing from pin 2 and 3 of the diagram then the car uses CANBUS ignition and will need interface 29-655-CAN
NOTE: on some cars, the steering wheel control wires are reversed, check and test for correct operation of the steering wheel controls before installing the new radio in the dashboard. If they are not as expected or reversed then the white and grey steering wheel control wires will need to have their positions swapped at the interface box.
What's Included
- 29-655 Steering Control Adaptor
- Stereo Patch Lead
Works with the following brands
- Alpine
- Clarion
- JVC
- Kenwood
- Pioneer
- Sony
- China Units
Patch lead INCLUDED for the steering controls depending on the make of radio being fitted.
| Radio Being Fitted | Part Number | Short Description |
| Resistive Programming (Loose Wire) | 29-000 | Loose wire Patch lead for 29-Series Steering wheel control for Resistive Programming, Chinese, Xtrons, Pumpkin, Joying or unbranded stereos. |
| Alpine | 29-001 | Patch lead for 29-Series Steering wheel control for Alpine stereos. |
| Clarion | 29-003 | Patch lead for 29-Series Steering wheel control for Clarion stereos. |
| JVC (Single Wire) | 29-004SW | Single Wire Patch lead for 29-Series Steering wheel control for JVC stereos. |
| Kenwood | 29-005 | Patch lead for 29-Series Steering wheel control for Kenwood stereos. |
| Pioneer | 29-007 | Patch lead for 29-Series Steering wheel control for Pioneer stereos. |
| Sony | 29-008 | Patch lead for 29-Series Steering wheel control for Sony stereos. |
| Resistive Programming (3.5 Jack) | 29-016 | 3.5mm Jack Patch lead for 29-Series Steering wheel control for Resistive Programming, Chinese, Xtrons, Pumpkin, Joying or unbranded stereos. |
| Universal | 29-025 | Self-Pinning Patch lead for Alpine, Kenwood, JVC (single wire), Pioneer, Sony and Chinese/Resistive programming head units with either two wires or a 3.5mm jack. |
TECHNICAL NOTE:
- CAR AUDIO FITTING ACCESSORIES ARE SOLD WITH LIMITED INSTRUCTIONS.
- SOME KNOWLEDGE OF CAR AUDIO INSTALLATION IS HELPUL IN CASE A MODIFICATION IN SOME RARE CASES MAY BE NECESSARY OR NEEDED.
IMPORTANT NOTE
- China Branded Headunit, please make sure your unit has 3 wires for connecting the patch lead to the car stereo that you are installing.
- Please make sure that is the correct Steering Control Adaptor for your vehicles by firstly checking to see if your make, model and year of car is listed in the advert. Secondly by checking to see if the connection in the picture is the same as you have in your vehicle. If the connection in the car is different from what you see in the picture then this adaptor is NOT suitable.
We try to provide upto date information. If you are unsure about the model number please feel free to contact our customer service and we will be happy to help you selecting correct stalk adaptor for your car.
